Server Fault Stack Exchange
Server Fault Stack Exchange

Questions tagged [zpool]

99 questions
17
votes
6 answers

Need to identify disk in zpool ... how?

I need to replace a bad disk in a zpool on FreeNAS. zpool status shows gptid/5fe33556-3ff2-11e2-9437-f46d049aaeca UNAVAIL 0 0 0 cannot open How do I find the serial # of that disk? More: glabel status gives: …
Dan
  • 889
  • 5
  • 14
  • 25
12
votes
3 answers

ZFS pool slow sequential read

I have a related question about this problem, but it got too complicated and too big, so I decided I should split up the issue into NFS and local issues. I have also tried asking about this on the zfs-discuss mailing list without much success. Slow…
Ryan Babchishin
  • 6,040
  • 2
  • 16
  • 35
12
votes
2 answers

Need to replace disk in zpool ... confused

I need to replace a bad disk in a zpool on FreeNAS. zpool status shows pool: raid-5x3 state: ONLINE scrub: scrub completed after 15h52m with 0 errors on Sun Mar 30 13:52:46 2014 config: NAME STATE …
Dan
  • 889
  • 5
  • 14
  • 25
10
votes
4 answers

Is it possible to detach and reattach a ZFS disk without requiring a full resilver?

I have a ZFS mirrored pool with four total drives. Two of the drives are intended to be used for rotating offsite backups. My expectation was that after the initial resilvering I could detach and later attach a disk and have it only do an…
STW
  • 930
  • 1
  • 7
  • 24
10
votes
4 answers

zpool status reports error ... what next?

On our FreeNAS server, zpool status gives me: pool: raid2 state: ONLINE status: One or more devices has experienced an unrecoverable error. An attempt was made to correct the error. Applications are unaffected. action: Determine if the…
Dan
  • 889
  • 5
  • 14
  • 25
8
votes
1 answer

ZFS vdevs accumulate checksum errors, but individual disks do not

I'm running a vendor-specific derivative of FreeNAS 9.3. My trouble started when I installed a new JBOD chassis to add two new vdevs into my pool, and the chassis had a bad board. During this time, I was seeing SAS power errors on the drives on the…
user260467
  • 275
  • 1
  • 12
7
votes
2 answers

zpool import: volume FAULTED with corrupted data, is it possible to save some data?

I was using Freenas 8.2 and decided to upgrade to 9.2. All seem to go well, upgraded zfs to 28 and rebooted. During next boot it seem to take forever and at some point I decided to turn off the machine. I guess this is what caused the problem. When…
Uphill_ What '1
  • 171
  • 1
  • 1
  • 5
6
votes
1 answer

ZFS on Linux/Ubuntu: Help importing a zpool after Ubuntu upgrade from 13.04 to 13.10, device IDs have changed

I have updated Ubuntu from version 13.04 to version 13.10, only to discover that the SATA disks IDs have changed, and my ZFS pool now fails. On new Ubuntu 13.10 the disk IDs are now ata-* instead of scsi-SATA_*. This is the pool status after the…
Manolo
  • 63
  • 1
  • 4
6
votes
2 answers

ZFS Recover from Faulted Pool State

I have a six disk ZFS raidz1 pool and had a recent failure requiring a disk replacement. No problem normally, but this time my server hardware died before I could do the replacement (but after and unrelated to the drive failure as far as I can…
Nick
  • 163
  • 1
  • 5
6
votes
1 answer

FreeNAS: Renaming a zpool

Now that our server is set up, I would like to rename our zpools. I read somewhere that the way to do this is export & re-import under the new name. But will all my mount points and shares remain intact? Or will I have to set those up again?
Dan
  • 889
  • 5
  • 14
  • 25
5
votes
1 answer

ZFS pool degraded on reboot

I have a Ubuntu server set up with a 14-disk ZFS raidz2 pool. About 80% of the time, on reboot, I will end up with a degraded pool with two of the disks marked as faulted. The drives that are faulted aren't always the same, but it is always exactly…
David Chappelle
  • 179
  • 5
5
votes
0 answers

ZFS restarts resilvering over and over again. Also very slow

Here's one of my Solaris 10 servers after a couple of disk replacements in a zpool pool: volume state: ONLINE status: One or more devices is currently being resilvered. The pool will continue to function, possibly in a degraded…
Pavel
  • 968
  • 1
  • 8
  • 29
5
votes
1 answer

ZFS shows pool state FAULTED, but all devices are ONLINE; how can I recover my data?

Our 100TB NAS based on FreeNAS 8 was unexpectedly powered off due to power failure. After turning it on back, 100TB zpool "projects" was unmounted with state "FAULTED". I've tried zpool import -fFX, it was running for about 20 hours, but nothing…
Sergey Andrianov
  • 51
  • 1
  • 6
5
votes
2 answers

Is it possible to change filesystem properties for an existing ZFS pool?

Suppose I created a pool with compression=on, and later wanted to turn off compression in-place - is that possible and if so how? I'm using Zevo CE on OS X in case that makes any difference (zpool version 28).
GJ.
  • 529
  • 1
  • 6
  • 21
5
votes
3 answers

how do I add a new disk to ZFS and make it available existing mountpoints if the current pool is root pool?

My S11 server has the following configuration: disk #1 is used for rpool, which is the root pool I want to add disk #2 to increase the size available for the already mounted folders, but I can't add the disk to the existing rpool because its the…
RaamEE
  • 195
  • 1
  • 1
  • 7
1
2 3 4 5 6 7